4-1 MACHINE LAYOUT Figure GE-1 shows the general layout of these machines. The rear of the drum is supported by a small shaft and bearing. The front of the drum is supported by glide pads. Older machines used two small glide pads underneath the drum for support (See figure GE-4) Newer machines have a 3-glide assembly attached to the inside front of the cabinet. The blower fan is attached directly to the front of the drive motor. The drive belt comes directly off the rear of the motor and goes completely around the drum. Electrical model GE dryers use a double heater element.
Secadora Centrales Secadora General Electric. $65.44 Kit de reparacion de secadoras, incluye el manual de instalacion. U$125.00 Motor Secadora electrica y a gas. Desmontar Puerta Estufa Electrica General Electric. General Electric Secadora Electrica Sge1437jmsbb un tiempo a esta parte en un electrodomestico sumamente util que tiene capacidad de.
Secadoras De Ropa Electricas
- Inicio Archivo Lavarropas (Lavadora)/ Secadoras General Electric. Lavarropas (Lavadora)/ Secadoras General Electric.
- Apr 18, 2018 General Electric Secadora Electrica Sge1437jmsbb un tiempo a esta parte en un electrodomestico sumamente util que tiene capacidad de 14 kilos de ropa. Tu secadora General Electric (GE) es un aparato valioso a tener, especialmente durante los meses frios del invierno cuando no puedes colgar tu ropa mojada.
General Electric Dryer Owner.s Manual. Otra ropa en la secadora. (en algunos modelos). Rios) de las lavadoras son las secadoras de ropa, que fueron inventadas en secadora para realizar el secado de la carga de ropa, fue. Secadora General Electric Secadora Kenmore. Incluye el manual de instalacion para. U$125.00 Motor Secadora electrica y a gas.
Funcionamiento de una lavadora General Electric Americana de 10 kg y funcionamiento de una. Manual MANUAL DE USO Y CUIDADO DEL REFRIGERADOR Este manual Manual Secadora Whirlpool Awz9813 lavadora whirlpool awm6100 service manual. Poco uso Sed de refrigerador estufa lavadora de platos y macrowey Estufa electrica whirlpool.
One of the two elements is energized for the low heat cycle; both heaters are energized for high heat. Late models have the heater elements contained in a cylindrical heater chamber fastened to the right front baseplate of the machine. In earlier models, the heaters are in a circular chamber directly behind the drum. 4-2 COMMON PROBLEMS The most common problems with these machines are: 1) Noisy operation. If you hear a very loud clattering sound, the belt could be broken. When the belt breaks in these machines, the tensioner touches the motor pulley and causes one heckuva loud racket. To confirm this diagnosis, check to see if the drum is turning.
Replace the belt as described in section 4-3. Another common cause of noise happens when the drum front support glides wear out. This causes a pronounced scrubbing sound (metal-to-metal.). 4-3 CABINET ACCESS PANELS (Fig. GE-3) ACCESS TO BELT TENSIONER,REAR BEARING OR GAS BURNER Each of these components has its own access panel: The gas burner access panel is located in the lower right front of the cabinet.
To open, push in on the top of the panel. The bottom is on nylon snaps and will pop off. Then just lift the panel out.
The belt tensioner is accessed through the bottom panel of the back of the dryer. The rear drum support bearing is accessed through the small panel in the center of the back of the dryer. In newer style machines, there is no access panel; you simply remove the cabinet top and front and slide the drum out. CABINET FRONT PANEL AND DRUM GLIDES Several different methods have been used to fasten the front panel to the cabinet top (figure GE-3). Unscrew the screws or pop the catches and lift the lid of the dryer.
NOTE: If you are testing the heaters of rear-heater models, the terminals are accessible at this point. Look to the rear of the drum on the right side. You can test them as described in section 4-6.
Secadora De Ropa Electrica
In bottom-heater models, you must remove the front panel as described below to test the heater element. Loosen, but do not remove, the two screws at the bottom front corners of the front panel of the cabinet. Unscrew the two screws at the top front corners inside the cabinet. Disconnect any door switch wires and lift off the front panel of the dryer. You can replace the belt at this point, without removing the drum. Release the belt tension as described in section 4-4.
You can slip the belt between the drum and the glides. Once the cabinet front panel is off, inspect the blower wheel at the lower left corner of the dryer for foreign debris, excessive lint or broken blades. The blower hub has a two-piece clamp which will fall apart if you remove it, so do not remove the hub clamp unless you plan to remove the whole motor and blower housing assembly as described in section 4-4.
Also while the cabinet front panel is off, inspect the felt seal inside the front panel for wear, excessive lint, or any debris that might be stuck to it. Remove and inspect the front drum support glides as shown in figure GE-4. Newer models have three glides attached to the inside of the front panel. Whether they're badly worn or not, it's a good idea to replace them as cheap insurance against future problems. Inside, you will see the drum support shaft and an 'E-'ring holding it in place. Remove the 'E-'ring with a small screwdriver.
If you have a magnet, you may also be able to use it to avoid dropping the ring inside the dryer. There are spacer shims between the bearing and the 'E-'ring. There are more shims inside the bearing, between the bearing and the drum. Some are nylon and some are metal. Note how they come off, and make sure you put the shims back on the same way they come off. Remove the cabinet front panel as described in section 4-3. In certain models, you will also need to remove the front drum support glides to get the drum out.
Once the cabinet front panel is off, you should be able to lift and slide the dryer drum straight outward. While the machine is open, vacuum out all accumulated lint. Be careful not to knock any wires loose. 4-5 BLOWER SERVICE If you need to replace the blower wheel on an old style machine, you must remove the dryer drum as described in section 4-4. Pull the six screws holding the blower housing to the baseplate, remove the motor mounting nuts and pull out the motor and blower housing as an assembly.
In some models, you must remove the tensioner arm to get the motor assembly out. When re-installing the blower, you must align the blower wheel so it does not touch the blower housing. To do this, loosen (but do not remove!) the clamp that holds the wheel to the motor shaft.
In rear-heater (circular) models, the elements must be pre-stretched to the correct length before installing. Follow the instructions that come with the new heaters.
Manual Secadora Electrica General Electric Smoker
DO NOT OVERSTRETCH THEM! It's better to leave them an inch or so short, and work them to the proper length when the heater element is in place in the dryer. Also, make sure you inspect the porcelain insulators and replace any that are cracked or broken. In bottom heater GE clothes dryer models, the whole heater chamber is replaced. Remove the two screws holding down the front end of the chamber and the back end just slips out of the heat riser.
Secadora De Gas
. 878 Answers SOURCE: You didn't state whether or not you were getting an error code.
On this model if the blower motor exceeds 3000 rpms for one minute the dryer will stop. Usually this is caused by a clogged or pinched vent hose or vent itself. Check this out first. You can find the tech sheet under the consol.
I believe it unscrews from the back and lifts up. This will give you detailed info on how to enter the diagnostic mode. If you cannot find the tech sheet, post back and the cat here will walk you through it. Catriver.post back. Posted on Oct 24, 2006.